تعليمات

Touch GunsWrap not very sticky. This is not a defect of the product, but rather determining the nature of the vinyl, because it is a repositioned material. The adhesive layer is activated at pressure and heat use. Before installing GunsWrap on a weapon, shop or accessory, it needs to be cleaned and degreased so that the vinyl can hold on to it. Clean the gun provides a clean installation. Here are a few products that we recommend using:

• Froglube solvent

• Gun scrubber

• CRC brake cleaner (non-chlorinated)

• Any gun-specific degreaser

We recommend you to use a small brush in all the grooves to remove oil and dirt. Then wipe it with a lint-free cloth or wash it in warm water , allow to dry. After using household or industrial degreasers, be sure to treat the surface with alcohol because they leave the film on the surface. In addition, denatured or isotropic alcohol as an independent degreasing agent is not suitable because it is not strong enough to completely clean the oil and grease of the weapon. New weapon New weapons tend to be more oily and may require more than one time degreasing. It would seem, why to clean the new weapon, but usually it is lubricated in the factory in order to preserve, and it needs to be well cleaned from grease, so that the material can be successfully glued. Before the installation, we recommend wiping the surface with alcohol to remove moisture. Composite and synthetic polymeric materials There are a few examples where additional attention is required to properly clean and prepare the surface before installation. If the butt and handguards are made of a composite material or synthetic polymer, a strong degreaser may be required. The molds used to make composite products are very lubricated to prevent the finished product from sticking to the mold. This lubricant remains on the butt and handkerchief surface and must be removed with a solvent so that the vinyl can stick to the surface. New weapons with plastic butt and handguards require additional cleaning, as the presence of oils will lead to loss of adhesion of vinyl. We saw excellent results when using brake cleaner (CRC BRAKLEEN GREEN US 397 G). After processing, the film should easily stick and press into each contour of the polymer material. Use heat from a heat gun or hair dryer to match the part shapes.

The safe handling of weapons is of paramount importance. GunsWrap made of high performance vinyl. To touch the surface will be comparable to a plastic butt or handpiece. For most customers, this will not be a problem when handling weapons. However, when installed on top of the notches on the handle and the handguards surface will lose some of the ribbing, to which you could get used. Another important feature of GunsWrap is the thickness and weight of the material. Camouflage GunsWrap has a thickness of 0.17 mm.(0,006 inch) GunsWrap will add to your weapon less than 200 grams (0.44 lbs) of additional weight. Our rigorous tests concluded that the added weight of the vinyl does not alter the ability to aim and shoot accurately. When installing the camouflage film on any weapon, it is necessary to trim the moving parts so as not to damage the functionality. Our templates are specially designed to cover fixed surfaces and leave important components intact. When trimming custom items, you need to use a sharp hobby knife and trim those parts yourself.

GunsWrap made from high performance vinyl with active heating. During the installation process it is required to heat the material with an even source of heat either from the heat gun or from the hair dryer. The material is designed to withstand high temperatures above 90 degrees Celsius (194 degrees Fahrenheit) on a regular basis. With heavy Skeet shotguns no change is noticed nebylo. From our rigorous testing, we concluded that the heat from the barrel would not affect The GunsWrap film . However, we do not recommend installing GunsWrap camouflage on the barrel, if you are going to shoot in full automatic mode. This can lead to discoloration of the material or melt. If you use your weapon only in automatic mode, we advise you not to paste over the barrel. (Actual only for automatic weapons AK series of and AR-15/M4) If you encounter any problems with GunsWrap camouflage as a result of the regular use of your firearm, please contact us and we will work to eliminate it.

GunsWrap is 100% waterproof. High performance vinyl is non-porous, which means that the material creates a sealed seal that also prevents water from entering or falling out. GunsWrap is weather resistant. Rain, hail, dirt or ice will not cause any problems during installation. Don't worry about loss of adhesion. GunsWrap has been designed for durability and everyday use.

Will the gun wrap camouflage film GunsWrap protect against rust? Yes, the material is non-porous and 100% waterproof. When properly installed, vinyl will not allow any water or oxygen to act on the surface of the weapon. It will seal and preserve the quality of the metal as it was before the application. This is one of the defining properties of the product, the protection of weapons not only from scratches but also from rust. However, GunsWrap should not be seen as a replacement for rust cleaning. If rust has already occurred, we recommend that you treat it before installing GunsWrap. If left untreated, GunsWrap vinyl removal can take some rusty flakes with it.

GunsWrap camouflage has been designed as a non-permanent alternative to weapon camouflage painting. Self-installation is quick and easy, allowing you to customize your weapons as you see fit. Since this is a vinyl app, GunsWrap is removable and does not affect the coverage of your weapons. To remove the material, heat the entire surface with a heat gun or hair dryer. Heat activates the material, causing separation between the part and the adhesive base. This makes the vinyl flexible and easy to peel off. We recommend you to start with a corner and twisting the tape out with your fingers. If the vinyl is removed without preheating, the connection between the vinyl and the surface remains intact. The film can peel off and leave a adhesive residue. When this happens, we suggest using alcohol and kerosene-based degreaser to remove glue residue.

One of the defining features of GusWrap camouflage wraps is that the cover is not permanent. These vinyl sets are removable and leave no residue on the surface of the weapon. Does this mean that the kits can be installed again at a later date? Unfortunately, the answer is no. GusWrap is intended for single use only. When the vinyl is removed, the glue can remain sticky to the touch. Why can't you just install it again? During the removal process, the material may distort, stretch or even break into smaller pieces.

GunsWrap offers pre-cut templates for popular models of firearms, air & AirSoft weapons such as smoothbore shotguns, PCP boppy and carbines, pistols, rifled carbines, submachine guns AR-15 and AK-47. However, there will be many models for which we will not have specific sets. In these cases , we recommend using a tape to wrap your weapon. The tape size is 20x100 cm. (7.8 x 39 inches). This will require the user to cut, install and trim the tape on their own to fit the weapon. It may take a little more time and effort, but the end result may look as clean and hassle-free as any other installation. Please follow our training instructions and installation tips to ensure a great installation.